BCT
TOP-UP LIST
整體學分承認 –
尚須選修科目表
|
Programme 課程 |
Bachelor of Science in Engineering Mechanics,
Materials and Design 工程力學、物料及設計學理學士 |
|
Precedent Code 尚須選修科目表編號 |
|
|
Maximum number of credits exempted 最高學分豁免 |
|
|
Top-Up Courses 尚須選修科目 |
Students are required to complete a total of 60 credits from the
following: (a) 20
credits from the courses labelled D2; (b) 40
credits from the courses labelled D1. (See courses at BCT Course Table EMMD-Appendix
1) Notes: (1) Courses
form excluded combinations with other courses. Only one of the courses in an excluded
combination can count towards a single OUHK award. Students should refer to the list of
excluded combinations at http://www.ouhk.edu.hk/excluded_combination
for the list of courses that form excluded combinations.
(2) Successful
completion of ELEC S203/ELEC S223 is considered as completion of ELEC S224. (3) Successful
completion of SCI S319/TC S319 and SCI S409/TC S409 are considered as
completion of ENGG S238. (4) MGT
B343 has been replaced by MGT B344 and MGT B345. Successful completion of MGT B343 is
considered as completion of MGT B344 and MGT B345. (5) Successful
completion of MECH S264 is considered as completion of DESN S217. (6) The
programme of Bachelor of Science in Engineering Mechanics, Materials and Design
and Bachelor
of Science with Honours in Engineering Mechanics,
Materials and Design will be phased out starting from April 2015. The University will
continue to confer the award of the degree of Bachelor of Science in Engineering Mechanics,
Materials and Design and Bachelor of Science with Honours in Engineering Mechanics, Materials and Design
up to June 2020. ************************************************ 學員需按下列要求完成
60 學分： (a) 選修 D2 類別的科目，取得 20 學分； (b) 選修 D1 類別的科目，取得 40 學分。 (可供修讀的科目見整體學分承認科目表 EMMD-Appendix
1) 備註： (1) 兩個或多個科目可以構成不可兼修的科目組合。同一組合內的科目不得同時計算入一項學術資格所需的總學分之內。同學需到以下網頁http://www.ouhk.edu.hk/excluded_combination閱覽最新的不可兼修的科目組合表。
(2) 已修畢 ELEC S203/ELEC S223 的學生，會視同已修畢 ELEC S224。 (3) 已修畢 SCI S319/TC S319 和 SCI S409/TC S409 的學生，會視同為已修畢
ENGG S238。 (4) MGT
B344 和 MGT B345 已取代 MGT
B343。已修畢 MGT B343 的學生，會視同已修畢 MGT B344 和 MGT B345。 (5) 已修畢 MECH S264 的學生，會視同已修畢 DESN S217。 (6) 工程力學、物料及設計學理學士及工程力學、物料及設計學榮譽理學士課程將於二○一五年四月起停辦。本校於二○二○年六月前仍繼續頒授工程力學、物料及設計學理學士及工程力學、物料及設計學榮譽理學士學位。 |
|
No. of Top-up Credits required to complete 需修讀的尚須選修學分 |
|
Revised 01/18 (seventeenth revision)