BCT TOP-UP LIST

整體學分承認 – 尚須選修科目表

 

Programme

課程

Bachelor of Science in Engineering Mechanics, Materials and Design

工程力學、物料及設計學理學士

Precedent Code

尚須選修科目表編號

EMMD-17

Maximum number of credits exempted

最高學分豁免

60

Top-Up Courses

尚須選修科目

 

Students are required to complete a total of 60 credits from the following:

 

(a)     40 credits from courses labelled D1, excluding MGT B240 and ENGG S228;

 

(b)     20 credits from courses labelled D2.

 

(See list of courses at BCT Course Table EMMD-Appendix 1)

 

Notes:

(1)     Courses form excluded combinations with other courses.  Only one of the courses in an excluded combination can count towards a single OUHK award.  Students should refer to the list of excluded combinations at http://www.ouhk.edu.hk/excluded_combination for the list of courses that form excluded combinations.

 

http://www.ouhk.edu.hk/REG/reg_aso/QR_ExCombination.png

 

(2)     Successful completion of ELEC S203/ELEC S223 is considered as completion of ELEC S224.

 

(3)     Successful completion of SCI S319/TC S319 and SCI S409/TC S409 are considered as completion of ENGG S238.

 

(4)     MGT B343 has been replaced by MGT B344 and MGT B345.  Successful completion of MGT B343 is considered as completion of MGT B344 and MGT B345.

 

(5)     Successful completion of MECH S264 is considered as completion of DESN S217.

 

(6)     The programme of Bachelor of Science in Engineering Mechanics, Materials and Design and Bachelor of Science with Honours in Engineering Mechanics, Materials and Design will be phased out starting from April 2015. The University will continue to confer the award of the degree of Bachelor of Science in Engineering Mechanics, Materials and Design and Bachelor of Science with Honours in Engineering Mechanics, Materials and Design up to June 2020.

 

************************************************

學員需按下列要求完成 60 學分：

 

(a)    選修 D1 類別的科目，取得 40 學分；但不得包括 MGT B240 及 ENGG S228；

 

(b)    選修 D2 類別的科目，取得 20 學分。

 

(可供修讀的科目見整體學分承認科目表 EMMD-Appendix 1)

 

備註：

(1)     兩個或多個科目可以構成不可兼修的科目組合。同一組合內的科目不得同時計算入一項學術資格所需的總學分之內。同學需到以下網頁http://www.ouhk.edu.hk/excluded_combination閱覽最新的不可兼修的科目組合表。

 

http://www.ouhk.edu.hk/REG/reg_aso/QR_ExCombination.png

 

(2)    已修畢 ELEC S203/ELEC S223 的學生，會視同已修畢 ELEC S224。

 

(3)    已修畢 SCI S319/TC S319 和 SCI S409/TC S409 的學生，會視同為已修畢 ENGG S238。

 

(4)    MGT B344 和 MGT B345 已取代 MGT B343。已修畢 MGT B343 的學生，會視同已修畢 MGT B344 和 MGT B345。

 

(5)    已修畢 MECH S264 的學生，會視同已修畢 DESN S217。

 

(6)    工程力學、物料及設計學理學士及工程力學、物料及設計學榮譽理學士課程將於二○一五年四月起停辦。本校於二○二○年六月前仍繼續頒授工程力學、物料及設計學理學士及工程力學、物料及設計學榮譽理學士學位。

 

No. of Top-up Credits required to complete

需修讀的尚須選修學分

60

Revised 01/18 (tenth revision)