BCT TOP-UP LIST

整體學分承認 – 尚須選修科目表

Programme 課程	Bachelor of Science with Honours in Engineering Mechanics, Materials & Design (with Management) 工程力學、物料及設計學(副修管理學)榮譽理學士
Precedent Code 尚須選修科目表編號	HEMMDM-06
Maximum number of credits exempted 最高學分豁免	30
Top-Up Courses 尚須選修科目	Students are required to complete a total of 130 credits from the following: (a) Obtain 70 credits from courses labelled CH in the BCT Course Table HEMMDM-Appendix 1a; (b) Obtain 10 credits from courses labelled FH in the BCT Course Table HEMMDM-Appendix 1a; (c) Obtain at least 20 credits from MECH S363, MECH S394, MECH S395 or MATH S361/MATH S365; (d) Obtain at least 10 credits from courses labelled BH in the BCT Course Table HEMMDM-Appendix 1a, excluding BUS B100 and BUS B103; (e) Remaining 20 credits from courses labelled HM & HH in the BCT Course Table HEMMDM-Appendix 1a which have not been used in fulfilling condition (c) above. (See courses at BCT Course Table HEMMDM-Appendix 1a) Notes: (1) Courses form excluded combinations with other courses. Only one of the courses of the excluded combinations can count towards an OUHK award. Students should refer to the list of Excluded Combinations attached to BCT Course Table HEMMDM-Appendix 1a for details. Students are also advised that this list will be updated by the University twice a year in the Prospectus and that students should refer to the updated list for information. (2) Students may have only one course from COMP S205 or COMP S201/COMP S210 or COMP S258 for counting towards the degree. (3) Successful completion of ECON A230 is considered as completion of ECON A231 and ECON A232. (4) Successful completion of LAW B260 is considered as completion of LAW B262 and LAW B263. (5) Successful completion of MATH S204/MATH S207 is considered as completion of MATH S221 and MATH S222. (6) Successful completion of ELEC S203/ELEC S223 is considered as completion of ELEC S224. (7) Successful completion of SCI S319/TC S319 and SCI S409/TC S409 are considered as completion of ENGG S238. (8) MGT B343 has been replaced by MGT B344 and MGT B345. Successful completion of MGT B343 is considered as completion of MGT B344 and MGT B345. (9) Successful completion of MECH S264 is considered as completion of DESN S217. (10) The programme of Bachelor of Science with Honours in Engineering Mechanics, Materials and Design (with Management) will be phased out starting from April 2015. The University will continue to confer the award of the degree of Bachelor of Science with Honours in Engineering Mechanics, Materials and Design (with Management) up to June 2020. ************************************************ 學員需按下列要求完成 130 學分： (a) 修畢整體學分承認科目表 HEMMDM-Appendix 1a 的 CH 類別科目，取得 70 學分； (b) 選修整體學分承認科目表 HEMMDM-Appendix 1a 的 FH 類別科目，取得 10 學分； (c) 選修 MECH S363， MECH S394， MECH S395 或 MATH S361/MATH S365，取得最少 20 學分； (d) 選修整體學分承認科目表 HEMMDM-Appendix 1a 的 BH 類別科目，取得最少 10 學分，但不得包括 BUS B100 及 BUS B103； (e) 選修整體學分承認科目表 HEMMDM-Appendix 1a 的 HM 及 HH 類別科目，取得 20 學分，但不得包括已計算入(c)項的學分。 (可供修讀的科目見整體學分承認科目表 HEMMDM-Appendix 1a) 備註： (1) 兩個或多個科目可以構成不可兼修的科目組合。若如是，大學只會將其中一科的學分計算在有關資格所需的總學分之內。詳情請參閱附錄在整體學分承認科目表 HEMMDM-Appendix 1a後的＜不可兼修的科目組合表＞。而不可兼修的科目組合的資料，亦詳載於課程概覽，大學每年均會將資料更新兩次。學員應參閱最新的課程概覽以取得最新的資料。 (2) 校方只會將 COMP S205 或 COMP S201 / COMP S210 或 COMP S258 其中一科計算入本學位課程之內。 (3) 已修畢 ECON A230 的學生，會視同已修畢 ECON A231 和 ECON A232。 (4) 已修畢 LAW B260 的學生，會視同已修畢 LAW B262 和 LAW B263。 (5) 已修畢 MATH S204/MATH S207 的學生，會視同已修畢 MATH S221 和 MATH S222。 (6) 已修畢 ELEC S203/ELEC S223 的學生，會視同已修畢 ELEC S224。 (7) 已修畢 SCI S319/TC S319 和 SCI S409/TC S409 的學生，會視同為已修畢 ENGG S238。 (8) MGT B344 和 MGT B345 已取代 MGT B343。已修畢 MGT B343 的學生，會視同已修畢 MGT B344 和 MGT B345。 (9) 已修畢 MECH S264 的學生，會視同已修畢 DESN S217。 (10) 工程力學、物料及設計學(副修管理學)榮譽理學士課程將於二○一五年四月起停辦。本校於二○二○年六月前仍繼續頒授工程力學、物料及設計學(副修管理學)榮譽理學士學位。
No. of Top-up Credits required to complete 需修讀的尚須選修學分	130

Revised 05/15 (thirteenth revision)